Rubber Feet for Speakers and Subwoofers (1-1/2" x 1-1/2")
Why speakers and subwoofers benefit from rubber feet, how they compare with spikes and pads, and how to fit a 1-1/2" x 1-1/2" screw-on foot to a cabinet.
Rubber Feet Warehouse |
News
Rubber Feet for Speakers and Subwoofers (1-1/2" x 1-1/2")
-
Cargo Trailer Ramp Door Bumpers: Sizes and Replacement (3-3/16" x 1-1/4")
The common 3-3/16" x 1-1/4" cargo trailer ramp door bumper: specifications, how to measure an old bumper, step-by-step replacement and bulk options for trailer builders.
Rubber Feet Warehouse |
-
Rubber Grommets for Electrical Panels, Control Cabinets and Knockouts
Knockout sizes and the grommets that fit them, enclosure wall thickness vs groove width, grommets for control cabinets, and why a grommet is not a cable connector.
Rubber Feet Warehouse |
-
How to Choose a Rubber Grommet for Your Hole and Panel Thickness
Choose a rubber grommet in four steps: measure the hole, match the groove to the panel thickness (with a steel gauge chart), size the ID and check flange clearance.
Rubber Feet Warehouse |
-
Sink Grid Rubber Feet: How to Measure and Replace Them
The little rubber feet on a stainless sink grid wear out and fall off, leaving bare wire to scratch the sink. How to measure the grid, pick replacement feet and...
Rubber Feet Warehouse |
-
Push-In Rubber Bumpers and Stem Bumpers: How to Measure and Choose
Push-in rubber bumpers (stem bumpers) snap into a hole with no screws or glue. How to measure the hole and panel, choose base size and height, and find the right...
Rubber Feet Warehouse |
-
Sliding Shower Door Rubber Stopper: How to Replace a Worn Bumper
When the little rubber stopper on a sliding shower door hardens or falls off, the glass bangs into the frame. How to find, measure and replace it, and the matching...
Rubber Feet Warehouse |
-
Rubber Tarp Straps: How to Choose, Size and Use Them Safely
Rubber tarp straps with S-hooks hold tarps and covers tight in sun, rain and cold. How to choose the material, size the stretch, space the straps and use them safely.
Rubber Feet Warehouse |
-
Heavy-Duty Rubber Bumper Pads: How to Choose Size, Hardness and Mounting
Heavy-duty rubber bumper pads protect doors, gates, docks and equipment from repeated impacts. How to pick the contact area, height, hardness and mounting style, with every pad we stock compared.
Rubber Feet Warehouse |
-
Rubber Grommets for Wires and Cables: How to Choose the Right Size
A rubber wire grommet is chosen by three measurements: the hole, the panel thickness and the cable bundle. How to measure each, which grommet suits electrical box knockouts, and how...
Rubber Feet Warehouse |
-
Rubber O-Rings: How to Measure, Size and Choose the Right One
Measure the inside diameter and cross-section, read the AS568 dash number, choose a compound for the fluid and temperature, then install without twisting. A practical guide to buying the right...
Rubber Feet Warehouse |
-
Rubber Washer Sizes: How to Measure ID, OD and Thickness (With Size Chart)
Rubber washers are sized OD x ID x thickness. Match the ID to your bolt, then choose the OD and thickness for sealing, cushioning or spacing. Bolt-to-washer table and a...
Rubber Feet Warehouse |
-
Gasket vs Washer vs O-Ring: What's the Difference and Which Do You Need?
A washer sits under a fastener, a gasket fills a flat joint between two parts, and an O-ring is squeezed in a groove. How to tell which one you need,...
Rubber Feet Warehouse |
